Morphological study of thin films: Simulation and experimental insights using horizontal visibility graph

We studied the morphological nature of various thin films such as silicon carbide (SiC), diamond (C), germanium (Ge), and gallium nitride (GaN) on silicon substrate Si(100) using the pulsed laser deposition (PLD) method and Monte Carlo simulation. We, for the first time, systematically employed the visibility algorithm graph to meticulously study the morphological features of various PLD grown thin films. These thin-film morphologies are investigated using random distribution, Gaussian distribution, patterned heights, etc. The nature of the interfacial height of individual surfaces is examined by a horizontal visibility graph (HVG). It demonstrates that the continuous interfacial height of the silicon carbide, diamond, germanium, and gallium nitride films are attributed to random distribution and Gaussian distribution in thin films. However, discrete peaks are obtained in the brush and step-like morphology of germanium thin films. Further, we have experimentally verified the morphological nature of simulated silicon carbide, diamond, germanium, and gallium nitride thin films were grown on Si(100) substrate by pulsed laser deposition (PLD) at elevated temperature. Various characterization techniques have been used to study the morphological, and electrical properties which confirmed the different nature of the deposited films on the Silicon substrate. Decent hysteresis behavior has been confirmed by current-voltage (IV) measurement in all the four deposited films. The highest current has been measured for GaN at ～60 nA and the lowest current in SiC at ～30 nA level which is quite low comparing with the expected signal level (μA). The HVG technique is suitable to understand surface features of thin films which are substantially advantageous for the energy devices, detectors, optoelectronic devices operating at high temperatures.     

基于残差决策的自动飞行控制系统远程实时故障诊断

针对自动飞行控制系统结构复杂、关联部件众多,发生故障时诊断时间长,从而影响飞机运行效率的问题,提出一种基于飞机通信寻址报告系统(ACARS)的远程实时故障诊断方案。首先,分析自动飞行控制系统的故障特点,设计搭建检测滤波器;然后,利用ACARS数据链实时发送的自动飞行控制系统的关键信息进行相关部件的残差计算,并根据残差决策算法进行故障诊断及定位;最后,针对不同故障部件残差间的差异大、决策门限无法统一的缺点,提出基于二次差值的残差决策改进算法,减缓了检测对象的整体变化趋势,降低了随机噪声和干扰的影响,避免了将瞬态故障诊断为系统故障的情况。实验仿真结果表明,基于二次差值的改进残差决策算法避免了多决策门限的复杂性,在采样时间为0.1 s的情况下,故障检测所需时间大约为2 s,故障检测时间大幅降低,有效故障检测率大于90%。     

重轨矫直速度对矫后残余应力的影响分析

针对矫直速度对重轨矫后残余应力的影响进行研究,利用Pro/E建立60kg·m-1重轨九辊水平矫直模型,采用ANSYS Workbench对重轨矫直过程进行有限元数值模拟,通过现场矫直规程对采用现场矫直速度以及假定矫直速度得到的重轨矫后残余应力进行分析比较,得出了在其余条件不变的情况下重轨的矫直速度在1.4~1.6m·s-1的范围内其轨底矫后纵向残余拉应力小于250MPa,且残余应力分布合理,满足矫直要求,相比于现场采用的1.2m·s-1的矫直速度其生产效率最大能够提高16.7%~33.3%。     

大采高综放工作面强动压端头顶板控制技术

为了解决大采高综放工作面回风侧端头顶板控制问题,针对马道头矿8211工作面的地质情况,通过对回风顺槽超前注浆加固,提高超前支护范围和支护强度,并对回风侧端头三角区煤壁和顶板进行化学浆加固的技术方案,有效控制了顺槽超前区围岩变形和工作面回风侧端头三角区煤壁片帮,保证了工作面端头区顶板安全。     

Ti-6Al-4V电弧熔丝增材轧制复合制造的有限元模拟

增材制造过程中由于在凝固及随后的冷却阶段易产生残余应力,从而影响部件的成形和使用。在增材过程中引入轧制工序,可望降低宏观残余应力,从而降低部件的变形。本文通过建立Ti-6Al-4V钛合金电弧熔丝增材与层间轧制复合成形过程的有限元模型,研究圆柱形轧辊条件下不同压下量对部件温度、应力、应变及残余应力分布的影响规律。结果表明,层间轧制可显著降低沉积层金属中的残余宏观应力；同时降低对基板的整体应力。采用圆柱形轧辊并增加压下量可显著降低宏观残余应力,还可以通过塑性变形改变材料的微观组织,提高材料性能,为复合增材工艺的优化指明了方向。     

Effects of welding parameters and welding sequence on residual stress and distortion in Al6061-T6 aluminum alloy for T-shaped welded joint

The distribution of temperature and then the distribution of residual stress and distortion in the stiffened aluminum alloy Al6061-T6 plates under the metal inert gas (MIG) welding process were investigated by three dimensional thermo-mechanical coupled finite element model using Ansys software. The properties of materials were considered temperature-dependent and the filler metal was added to the workpiece by the element birth and death technique. In three modes of current, two different speeds and two various sequences, the distribution of residual stress and distortion were calculated and analyzed. The results showed that increase in welding speed decreased the vertical deflection in the plate, transverse shrinkage and angular distortion of plate and the lateral deflection of stiffener, but increased the maximum longitudinal tensile stress in the plate and stiffener. Furthermore, increase in current increased the residual stress and deformation in the plate and stiffener, and the change in the welding sequence changed the distribution of the distortion in the plate and the stiffener without significant change in the distribution of the longitudinal residual stress.     

北斗三星无源定位技术

介绍了北斗双星定位系统的特点、功能、系统组成和工作原理,说明了北斗有源定位方式在应用方面的局限性。针对北斗有源定位方式不能无线电静默,和人们对具有无线电隐蔽性的卫星定位的需求,详细介绍一种北斗三星无源定位技术:包括工作原理、实现方法、定位精度分析和目前达到的定位精度。阐述了北斗三星无源定位技术的优点和应用形势。     

脉冲中子组合测井在胜利油田中的应用

碳氧比能谱、脉冲中子衰减-能谱、注硼中子寿命以及氧活化测井均属于脉冲中子测井方法.简单介绍了这些测井技术各自的测量原理及应用.针对胜利油田地质情况的复杂性、多解性,阐述了应用组合测井方法可以更好地解决油藏的剩余油分布等问题.使用脉冲中子衰减-能谱测井仪(PND)进行PND和硼中子寿命测井的组合测井方法,利用PND获得的俘获截面曲线作为注硼中子寿命测井的基线.该方法既可缩短施工时间,又可解决单一测井方法无法解决的某些特殊测井问题.介绍了应用这种组合测井在正确识别低压储层、确定储层窜通情况、获得剩余油饱和度、确定储层水淹程度等方面的测井实例.